QYZL-6A
智能一体化蒸馏仪
220V/50HZ
智能一体化蒸馏仪厂家信息,产品信息可到 该网站查看~
型 号 | 速度 | 加热功率 | 功能 |
QYZL-6A | 蒸馏速度:12ml/min | 加热功率:0-2700W | 普通型:加热+定时,风冷 |
QYZL-6B | 蒸馏速度:12ml/min | 加热功率:0-2700W | 智能型:加热+定时+称重,水冷 |
12、 额定电压/频率:220V/50HZ
1. Connect the hose with the condenser water, and connect the vacuum hose with the vacuum pump.
2. Inject the water into the heating tank first. It is best to use pure water and tap water for 1-2 days.
3. Adjust the Angle of the main host: just release the host and the column connecting screw. The host can be tilted anywhere between 0 and 45 degrees.
4. Connect the condenser water, connect the power source 220V/50Hz, connect the evaporating bottle on the main machine (do not let go), and open the vacuum pump to make sure the vacuum degree is released.
5. Adjust the height of the main engine: press the pressure bar at the bottom of the heating tank, and adjust the curve to the right position to reach the desired height.
6. Turn on the speed control switch, light the green light, adjust the speed knob on the left side, and the evaporation bottle starts to turn. Turn on the thermostat, light the green light, and adjust the left side.
Adjust the knob, the heating tank starts the automatic temperature control heating, the instrument enters the test run. Temperature and vacuum degree one to the required range, that is, can evaporate the solvent to accept the bottle.
7, intelligent integration of distillation apparatus vaporized, first closing speed switches and temperature switches, push down lever to increase host, and then close the vacuum pump, and open the vent valve at the top of the condenser,
Connect it to the atmosphere, remove the evaporating bottle, and the evaporation process ends.
智能一体化蒸馏仪操作规程
1、用胶管与冷凝水龙头连接,用真空胶管与真空泵相联。
2、先将水注入加热槽。用纯水,自来水要放置1-2天再用。
3、调正主机角度:只要松开主机和立柱连结螺钉。主机即可在0-45度之间任意倾斜。
4、接通冷凝水,接通电源220V/50Hz,与主机连接上蒸发瓶(不要放手),打开真空泵使之达一定真空度松开手。
5、调正主机高度:按压下位于加热槽底部的压杆,左右调节弧度使之达到合适位置后手离压杆即可达到所需高度。
6、打开调速开关,绿灯亮,调节其左侧旁的转速旋钮,蒸发瓶开始转动。打开调温开关,绿灯亮,调节其左侧旁的
调温旋钮,加热槽开始自动温控加热,仪器进入试运行。温度与真空度一到所要求的范围,即能蒸发溶剂到接受瓶。
7、智能一体化蒸馏仪蒸发完毕,首先关闭调速开关及调温开关,按压下压杆使主机上升,然后关闭真空泵,并打开冷凝器上方的放空阀,
使之与大气相通,取下蒸发瓶,蒸发过程结束。