广州鑫图科技有限公司
主营产品：GPS北斗天线、北斗GPS模块、GMOUSE
【官方微信小程序】
GS-96U7
Autonoous<2.5averagem
16.0 * 12.2 * 2.4mm
其他
720h
好
广东省广州市天河区
1、产品描述
GS-96U7模块是一个低功耗主芯片的超小外型GPS接收模组，该产品采用了新一代U-blox芯片，超高灵敏度，具备功能，能满足定位的严格要求。内嵌在使用GPS服务的智慧型手机、平板电脑、PND、DVR、可携式装置，测量设备，人员定位管理，测速设备，授时设备，交车跟踪定位、出租车跟踪定位、公司车辆跟踪定位、物流车辆跟踪定位、汽车故障检测、汽车油量检测、汽车物联网、挖掘机定位等等。
2、产品应用：
GPS 应用在 PDA、Pocket PC 和其他便携设备领域
个人定位和汽车定位等轨迹追踪产品
面积测量及距离测量等测绘产品
同步 UTC 时间及授时领域
轨迹记录及 GPS 数据点校准等产品
3、产品优点：
单面表贴，二次 SMT 方案，更快速的应用
采用无铅工艺制造，符合 RoHS 标准
UART / TTL，USB2.0 可选输出
采用 KDS 0.5PPM 高精度 TCXO
丰富的数据输出速率：9600bps(默认) [可选:1200,2400,4800，19200，38400，57600，115200，230400，460800,921600]
可任意设置搭配输出语句：NMEA 0183 V3.0(GGA, GSA, GSV, RMC, VTG, GLL)
内建 RTC 晶体
支持可调的数据刷新率：1Hz-10Hz
卫星质量控制：丰富的设置卫星质量控制及防止飘逸软体设置
应用场景：从步行模式-车载模式-静态模式-便携模式-空降模式及 2D&3D定位用户可以自由设置
支持定位 PPS 指示灯：未定位前常亮或者关闭；定位后闪烁
支持 AssistNow Online 和 AssistNow Offline 等 A-GPS 服务
GPS、GALILEO、SBAS（WAAS、EGNOS、MSAS、GAGAN）混合引擎
4、模块参数表
5、模块工作原理
6、模块信号侧视图及RF射频属性图
7、模块管脚分配
| Pin NO. | Pin Name | I/O | Description | Remark |
| 1 | Reserved | - | Reserved | Leave open. |
| 2 | Reserved | I/O | SPI Select | Leave open if not used. |
| 3 | TIMEPULSE | O | Timepulse Signal | Configurable Timepulse signal (one pulse per second by default). Leave open if not used |
| 4 | EXTINT0 | I | External Interrupt | External Interrupt Pin. Internal pull-up resistor to VCC. Leave open if not used. |
| 5 | USB_DM | I/O | USB I/O line | USB2.0 bidirectional communication pin. Leave open if unused. |
| 6 | USB_DP | I/O | USB I/O line | Implementation see Section 0 |
| 7 | VDDUSB | I | USB Power Supply | To use the USB interface connect this pin to 3.0 – 3.6 V. If no USB serial port used connect to GND. |
| 8 | RESET | I | Reserved | Leave open. Can be used as a RESET_N input. |
| 9 | VCC_RF | O | Output Voltage RF section | Pins 8 and 9 must be connected together. VCC_RF can also be used to power an external active antenna. |
| 10 | GND | I | Ground | Assure a good GND connection to all GND pins of the module, preferably with a large ground plane |
| 11 | RF_IN | I | GPS signal input from antenna | The connection to the antenna has to be routed on the PCB. Use a controlled impedance of 50 Ω to connect RF_IN to the antenna or the antenna connector.. |
| 12 | GND | I | Ground | Assure a good GND connection to all GND pins of the module, preferably with a large ground plane |
| 13 | GND | I | Ground | Assure a good GND connection to all GND pins of the module, preferably with a large ground plane |
| 14 | Reserved | I | Reserved | Leave open |
| 15 | Reserved | I | Reserved | Leave open |
| 16 | CFG_GPS0 | I/O | Config. Pin/SPI SCK | Leave open if not used. |
| 17 | Reserved | I | Reserved | Leave open |
| 18 | SDA2 | I/O | DDC Pins | DDC Data. Leave open, if not used. |
| 19 | SCL2 | I/O | DDC Pins | DDC Clock. Leave open, if not used. |
| 20 | TxD1 | O | Serial Port 1 |
|
| 21 | RxD1 | I | Serial Port 1 | 3.6 V tolerant serial input. Internal pull-up resistor to VCC. Leave open if not used. |
| 22 | V_BCKP | I | Backup voltage upply | It’s recommended to connect a backup battery to V_BCKP in order to enable Warm and Hot Start features on the receivers. Otherwise connect to GND. |
| 23 | VCC | I | Supply Voltage | Max allowed ripple on VCC=50 mVpp |
| 24 | GND | I | Ground | Assure a good GND connection to all GND pins of the module, preferably with a large ground plane |
8、推荐应用电路
